Mounting A Tub
Mounting A Tub
Blog Article
Were you hunting for information and facts around A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't precisely rocket science, however it does need strong plumbing, carpentry, and sometimes, tiling skills. Replacing an old tub with a new one is likewise a moderately challenging job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall to remove the old tub as well as place the brand-new bath tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will need an assistant to leave the old bathtub and also embeded in the brand-new one. See to it you have qualified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take over a halfway-completed job, it is much better to think about utilizing one prior to you start. Possibilities are you might need a specialist plumber to make tube links.
This post will certainly assist you set up a brand-new tub in your shower room if you have actually already gotten a new tub and don't need to change the plan of your previous supply of water pipelines.
Your devices as well as product list ought to comprise the following:
Planning for the Installment
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next, fit the taps or mixer to the bath tub. When suitable the tap block, it is essential to see to it that if the faucet includes a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to prevent stress on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom need to now prepare to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any kind of water remaining in the system. The procedure of removing the existing taps can be fairly problematic as a result of the limited access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel ready for the remaining water that will come from the pipelines. As soon as the supply pipes have actually been gotten rid of, use the exact same device to loosen the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing compound.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Making use of both wood boards under its feet, put the bath tub in the called for placement. The wood boards are practical in equally spreading the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the level as well as changing the feet on the tub up until the level checks out level.
To set up taps, fit the bottom of the furthest flexible faucet adapter to the proper supply pipeline by making a compression sign up with; then do the exact same for the other tap.
Switch on the water supply and also examine all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as additionally examine the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, take care of the bath paneling as defined in the maker's user's manual. Tiling as well as securing around the tub ought to wait up until the bathtub has been used at least when as this will certainly resolve it right into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the various other end gives a link to the existing supply pipes.
If you need to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the common 15mm supply pipe.
Next, place the tap in the mounting hole in the bath/basin ensuring that the washing machines are in place in between the tap and also the sink. Protect the tap in position with the producer given backnut. When the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet ports. The previous type must be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack a stiff seal, causing the water to pass through the wall in between the bath and also the tiling, causing complications with wetness and feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a larger space to load, you can fill it with spins of soaked paper or soft rope. Remember to always fill the bath tub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealant can fracture fairly early if you do not think about this movement before sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are likewise conveniently readily available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or waterproof sticky as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a fervent reader about How to Install a Bathtub Yourself, I figured sharing that excerpt was important. Don't hesitate to take a moment to promote this post if you enjoyed it. Thank you so much for going through it.
Schedule Service Now
Report this page